What did you use your sebenza for today?

7CA04BE2-11E0-4540-AEC2-BF2B5E0BFD00.jpeg 47457B79-8417-43C5-AB64-A17F0D5ACC2F.jpeg 0709AB1F-4C6C-4FD2-B7C2-3A89908E53C0.jpeg 0D61D76A-14BD-4FB1-9B8E-2913927FEA90.jpeg DEE5788A-DF79-4C82-9C9B-0881123F61F4.jpeg C082ACB4-84E4-4679-9430-2A0D04E006A8.jpeg CDFE7D6D-BEC4-4249-AE9F-C6A2C77C8175.jpeg 772D94BD-ABD7-4FC5-8307-2EA2E8F57249.jpeg 3E09C791-54CB-4D45-B2D0-63C72B08EE17.jpeg 77E721B9-B016-4719-8367-0FF9839D1E77.jpeg Opened several light packages, cut a ton of jetline. Pulled several low voltage lights in and stripped the cords on them. Scored some silicone to take a cover off, opened my sons toothbrush, cut tape. Cut some jetline to put on a sump pump to lower in a hole
 
That panelboard looks like its seen better days....

Keep safe brother.
No doubt about it. It’s outside and the weather has taken a toll on it. Had a main breaker burn. Well actually the fingers behind it burnt on B phase. I got them back up and running temporarily. Had a breaker in stock, it’s 480volt not 208 but it’ll work, finger kit is being next day aired.
 
DIY at home.
zkPEteb.jpg
 
78D476EB-5864-4785-BB4E-8852598178EA.jpeg FD305DC6-24DA-48AD-BE2D-115AFE1C3D3B.jpeg 68FBC632-B47B-406F-B4EF-73923C65D94E.jpeg C3DD4051-49F9-4F58-9503-C02BA0135C47.jpeg 089EFAEF-A2DB-45F0-B196-7CE1A1FDEBDD.jpeg 486F309F-4C18-42D6-8D8E-77A9D8513164.jpeg A4ECE3C6-650A-4C8F-A8B4-5EA0C3F2E82B.jpeg 46D5220A-95F7-4A33-8988-071A89CC1245.jpeg 7C1A156B-E0E0-40F3-B0D9-39547C26E960.jpeg Scored some Sheetrock, I knew there were old wires just notched in the joist so didn’t want to run sawzall thru them. Opened several packages. Stripped some romex. In order to change out the fingers on the panelboard and the bad breaker, I had to take the other breaker out across from it as well. The feeds weren’t marked so I taped the phases before taking the wires out to make sure they went back correct
 
Last edited:
4BF778B6-6C50-4DEA-ACF1-BD3189A122D2.jpeg CF0C5185-FE1E-493A-A5E6-5F03F38631DF.jpeg 93683476-09D5-4F2E-BAD8-E23E31E8C757.jpeg 83B14037-E30D-49B7-9359-0A42ABA71347.jpeg C1D195CC-E2D0-49F2-A0D8-20E98568D6EF.jpeg 0F3D2BEC-3FCE-4575-804E-B85A5425ED3E.jpeg 7FFFE654-C9A5-44FA-ACDA-7119707C9743.jpeg 679F54EA-010D-4C88-B750-C6E8107F82B1.jpeg 2A93BA16-FDE8-4139-8488-66AE3A36BDBD.jpeg Ended up at several places today. Installed some 12volt under cabinet lites. Stripped some 14/2 Romex and opened the packages. That’s the only time we use 14/2, on the low voltage side of the driver. Just can’t bring myself to use 14wire and 15amp circuits. Cut some tape and ended up back doing some more work on Cat6 cameras putting ends on the wire. Separated some foil tape from its backing
 
Cut some fisher plugs to size to fit the length of the hole.

Shops were closed and needed to fix a piece of fence that was moving a bit.

203-F2890-5-BEF-4-F82-8-FBB-699393-A40417.jpg


Also unpacked the new ladder

7-F4-B7-A45-CF74-492-A-8-CF0-0880-B58-A17-B8.jpg
What color thumb studs did your Insingo start out with? Whoop, still blue, just dirty in that one picture.
 
Last edited:
Back
Top